IDENTIFICATION DES PARAMÈTRES D'UN MOTEUR À COURANT CONTINU EXCITÉ SÉPARÉMENT À L'AIDE D'UNE MÉTHODE DE PÁSEK AUTOMATISÉE
DOI:
https://doi.org/10.59277/RRST-EE.2026.4.4Keywords:
Identification des paramètres, Machine à courant continu à excitation séparée, Méthode de Pasek graphique, Méthode de Pasek automatiséeAbstract
Cet article traite de l'identification des paramètres d'une machine à courant continu à excitation séparée par la méthode de Pasek, modifiée afin d'automatiser entièrement la procédure. Pasek a proposé une procédure expérimentale, suivie d'un processus d'identification, permettant de déterminer, à partir d'un seul essai et sous certaines hypothèses simplificatrices, cinq paramètres d'une telle machine. La méthode de Pasek réduit considérablement le temps d'identification ; cependant, elle comporte une étape graphique qui nécessite une intervention humaine et est sujette à des erreurs de mesure. Dans cet article, nous proposons une approche automatisée qui élimine l'étape graphique en la remplaçant par un traitement informatique des données, réduisant ainsi le temps d'identification et automatisant entièrement la procédure. La procédure proposée est mise en œuvre à des fins expérimentales et ses résultats sont comparés à ceux de la méthode d'identification classique.
References
(1) M. Kuczmann, “Review of DC motor modeling and linear control: theory with laboratory tests,” Electronics, 13, 11, Art. no. 2225 (2024).
(2) R. Belal, M. Flitti, M.L. Zegai, “Tuning of PI speed controller in direct torque control of dual star induction motor based on genetic algorithms and neuro-fuzzy schemes,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 69, 1, pp. 9–14 (2024).
(3) D.I. Völlmecke, “Parameter identification of DC motors,” Technical report, IMC Berlin (2013).
(4) M.F. Fazdi, P.-W. Hsueh, “Parameter identification of a permanent magnet DC motor: a review,” Electronics, 12, 12, Art. no. 2559 (2023).
(5) S.S. Saab, R. Abi Kaed-Bey, “Parameter identification of a DC motor: an experimental approach,” Proc. 8th IEEE Int. Conf. Electronics, Circuits and Systems (ICECS), 2, pp. 981–984 (2001).
(6) G.Á. Szíki, A. Szántó, É. Csernusné Ádámkó, “Review of methods for determining the moment of inertia and friction torque of electric motors,” Acta Polytech. Hung., 21, 4, pp. 203–218 (2024).
(7) C.O. Gökçe, M.E. İpek, M. Dayıoğlu, R. Ünal, “Parameter estimation and speed control of a real DC motor with a low-resolution encoder,” Results Control Optim., 19, Art. no. 100549 (2025).
(8) R. Majdoubi, L. Masmoudi, M. Bakhti, A. Elharif, B. Jabri, “Parameter estimation of BLDC motor based on physical approach and weighted recursive least squares algorithm,” Int. J. Electrical and Computer Engineering, 11, 1, pp. 133–145 (2021).
(9) M. Hadef, M.R. Mekideche, “Parameter identification of a separately excited DC motor via inverse problem methodology,” Turkish J. Electr. Eng. Comput. Sci., 17, 2, pp. 99–106 (2009).
(10) J.A. Cardona Soto, I.U. Ponce, I. Soto, M.A. García, G. Mejía, “Identification of dynamic parameters in a DC motor using step and ramp torque response methods,” Sensors, 26, 1, Art. no. 78 (2025).
(11) N. Khac Tung, S.M. Vlasov, “Algorithm for identification of DC motor parameters by method of dynamic expansion of regressor and mixing,” J. Sci. Tech. Inf. Technol., Mech. Opt., 21, 1, pp. 130–134 (2021).
(12) A. Sebhi, A.C. Megherbi, A. Dendouga, A. Zitouni, “Identification of DC motor parameters using the ZOA metaheuristic algorithm with comparative study,” J. Electr. Eng. Renew. Energy Dev., 1, 1, pp. 1–8 (2025).
(13) K.H. Chao, K.H. Huang, Y.H. Guo, “Design of a brushless DC motor drive system controller integrating the Zebra Optimization Algorithm and sliding mode theory,” Electronics, 14, 17, Art. no. 3353 (2025).
(14) J.C. Gamazo-Real, V. Martínez-Martínez, J. Gomez-Gil, “ANN-based position and speed sensorless estimation for BLDC motors,” Measurement, 188, Art. no. 110602 (2022).
(15) M. Raissi, P. Perdikaris, G.E. Karniadakis, “Physics-informed neural networks: a deep learning framework for solving forward and inverse problems involving nonlinear partial differential equations,” J. Comput. Phys., 378, pp. 686–707 (2019).
(16) J. Stiasny, G.S. Misyris, S. Chatzivasileiadis, “Physics-informed neural networks for non-linear system identification for power system dynamics,” Proc. 2021 IEEE Madrid PowerTech, Madrid, Spain, pp. 1–6 (2021).
(17) S. Ayankoso, P. Olejnik, “Time-series machine learning techniques for modeling and identification of mechatronic systems with friction: a review and real application,” Electronics, 12, 17, Art. no. 3669 (2023).
(18) Z. Pásek, “Nový způsob určení základních dynamických parametrů stejnosměrného motoru” [“A new method for determining the basic dynamic parameters of a DC motor”] (in Czech), Elektrotechnický Obzor, 51, pp. 109–114. https://fliphtml5.com/xgdg/ihme/Elektrotechnick%C3%BD_obzor_1958_-_1969/ (1962).
(19) H.A. Toliyat, G.B. Kliman, “Handbook of electric motors,” 2nd ed., CRC Press (2018).
(20) K.J. Åström, T. Hägglund, “Advanced PID control,” ISA – The Instrumentation, Systems, and Automation Society. https://www.semanticscholar.org/paper/Advanced-PID-Control-%C3%85str%C3%B6m-Hagglund/be4405ec46a026a6f602a260765d794a55f0b951 (2006).
(21) J.G. Ziegler, N.B. Nichols, “Optimum settings for automatic controllers,” Trans. ASME, 64, 8, pp. 759–765 (1942).
(22) A. Batool, N. ul Ain, A.A. Amin, M. Adnan, M.H. Shahbaz, “A comparative study of DC servo motor parameter estimation using various techniques,” Automatika, 63, 2, pp. 303–312 (2022).
(23) S.P. Perumalsamy, V. Narayanasamy, K.P. Arunachalam, P. Balasubramanian, “Evaluation for thermal analysis of DC motors in electric vehicles,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 71, 1, pp. 151–156 (2026).
(24) M.M. Rădulescu, A.A. Pop, “Experimental determination of linear dynamic model parameters of the separately excited brushed DC motor by modified Pásek’s method,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 67, 3, pp. 271–274 (2022).
(25) M.M. Rădulescu, “Transient processes in classical rotating electric machines I” (in Romanian), Casa Cărții de Știință (Science Book Publishing House), Cluj-Napoca, pp. 475–480 (2022).
(26) M. Jesenik, M. Ravber, M. Trbušić, “Innovative approach for the determination of a DC motor’s and drive’s parameters using evolutionary methods and different measured current and angular speed responses,” Mathematics, 12, 1, Art. no. 42 (2023).
Downloads
Published
Issue
Section
License
Copyright (c) 2026 REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.