ELECTRICAL CIRCUIT INFLUENCE ON THE RESPONSE OF STRUCTURALLY OPTIMIZED PIEZOELECTRIC HARVESTERS
DOI:
https://doi.org/10.59277/RRST-EE.2026.4.3Keywords:
Piezoelectric energy harvester, Structural optimization, Electrical circuit, Triangular cantilever, Finite element analysis (FEA), Microelectromechanical systems (MEMS)Abstract
The paper investigates the influence of an electrical circuit on the electrical and mechanical behavior of structurally optimized piezoelectric energy harvesters. A quadmorph cantilever piezoelectric harvester comprising four PZT-5H active layers is analyzed. Structural optimization is pursued by reducing the piezoelectric material towards a triangular longitudinal section, comparing the performance with the original rectangular structure. Finite element simulations have been conducted, employing a digital twin with a full coupling of Solid Mechanics, Electrostatics, and Electrical Circuit physics interfaces. The electrical circuit emulates the finite input impedance of the spectrum analyzer used in the laboratory. Introducing the electrical impedance shifts the response parameters of interest in both mechanical and electrical domains, changing resonant frequency, stress, displacement, and voltage due to electromechanical coupling. The performance of the optimized structures is evaluated in terms of electrical response per unit volume of piezoelectric material under two relevant approaches: the same inertial mass and the same mechanical stress. The results demonstrate that the triangular structure enables a more efficient use of piezoelectric material, while significantly reducing material volume. The simulations with an electrical circuit indicate its potential use for fine-tuning.
References
(1) C. Săvescu, D. Comeagă, M. Roman, D. Lale, R. Stoica, E. Vasile, C. Nechifor, A. Stoicescu, “Experimental study of a piezoelectric harvester vibrating on an industrial screw compressor,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 70, 1, pp. 9–14 (2025).
(2) C. Săvescu, V. Petrescu, D. Comeagă, I. Vlăducă, C. Nechifor, F. Niculescu, “Vibration analysis of a twin-screw compressor as a potential source for piezoelectric energy harvesting,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 68, 3, pp. 253–258 (2023).
(3) C. Săvescu, D. Comeagă, A. Morega, Y. Veli, “Experimental tests with piezoelectric harvester for tuning resonant frequency to vibrating source,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 67, 4, pp. 457–460 (2022).
(4) A. Ounissi, A. Kaddouri, M.-S. Aggoun, R. Abdessemed, “Second order sliding mode controllers of micropositioning stage piezoelectric actuator with Colman-Hodgdon model parameters,” Rev. Roum. Sci. Techn. – Électrotechn. et Énerg., 67, 1, pp. 41–46 (2022).
(5) R.G. Ballas, “Piezoelectric bending transducers: the physics of their static and dynamic behaviour: a textbook about indispensable actuators in microtechnology, mechatronics and medical technology,” Springer, Berlin, Heidelberg (2025).
(6) S. De Caro, R. Montanini, S. Panarello, A. Quattrocchi, T. Scimone, A. Testa, “A PZT-based energy harvester with working point optimization,” 2017 6th International Conference on Clean Electrical Power (ICCEP), pp. 699–704 (2017).
(7) M. Ashford, B. Onyenucheya, J. Zirnheld, K. Burke, “Improving a piezoelectric energy harvester output using a synchronized switch harvesting design,” 2021 IEEE Pulsed Power Conference (PPC), pp. 1–5 (2021).
(8) D. Zhu, S. Beeby, J. Tudor, N. White, N. Harris, “Improving output power of piezoelectric energy harvesters using multilayer structures,” Procedia Engineering, 25, pp. 199–202 (2011).
(9) A. Pasharavesh, H. Dalir, “Flexural modes coupling in cantilever-type piezoelectric energy harvesters,” Energy Reports, 7, pp. 6438–6450 (2021).
(10) D. Benasciutti, L. Moro, S. Zelenika, E. Brusa, “Vibration energy scavenging via piezoelectric bimorphs of optimized shapes,” Microsystem Technologies, 16, 5, pp. 657–668 (2010).
(11) V.J. Caetano, M.A. Savi, “Multimodal pizza-shaped piezoelectric vibration-based energy harvesters,” Journal of Intelligent Material Systems and Structures, 32, 20, pp. 2505–2528 (2021).
(12) P. Skėrys, R. Gaidys, “A dynamic analysis of a cantilever piezoelectric vibration energy harvester with maximized electric polarization due to the optimal shape of the thickness for first eigen frequency,” Applied Sciences, 15, 13, Art. no. 7525 (2025).
(13) V. Hassani, T. Tjahjowidodo, “Structural response investigation of a triangular-based piezoelectric drive mechanism to hysteresis effect of the piezoelectric actuator,” Mechanical Systems and Signal Processing, 36, 1, pp. 210–223 (2013).
(14) C. Borzea, D. Comeagă, Y. Veli, A. Săvescu, “Piezoelectric cantilever harvester with trapezoidal/triangular section for increased conversion efficiency,” Iberian COMSOL Multiphysics Conference 2022, pp. 54–57 (2022), https://www.researchgate.net/publication/363710805_Piezoelectric_Cantilever_Harvester_with_TrapezoidalTriangular_Section_for_Increased_Conversion_Efficiency.
(15) J. Erhart, P. Půlpán, M. Pustka, “Piezoelectric ceramic resonators,” Springer International Publishing, Cham (2017).
(16) C. Săvescu, D. Comeagă, A. Stoicescu, “Optimization of cantilever piezoelectric harvester to triangular shape with material reduction using finite element analysis,” Heliyon, 10, 13, Art. no. e33209 (2024).
(17) C. Săvescu, D. Comeagă, M. Roman, A. Stoicescu, C. Nechifor, M. Beldiman, “Maximizing the power output of a piezoelectric harvester by optimal resistive load,” 14th International Symposium on Advanced Topics in Electrical Engineering (ATEE) (2025).
(18) Midé Technology, “PPA products datasheet & user manual.” https://cdn2.hubspot.net/hubfs/3841176/Data-Sheets/ppa-piezo-product-datasheet.pdf (2017).
(19) COMSOL, “Structural mechanics module user’s guide.” https://doc.comsol.com/6.1/doc/com.comsol.help.sme/StructuralMechanicsModuleUsersGuide.pdf (2022).
(20) C. Borzea, D. Comeagă, A. Săvescu, “Boosting the electric output of a cantilever piezoelectric harvester by tip curvature blocking elements,” 8th European Conference on Renewable Energy Systems (ECRES 2020), pp. 344–350 (2020), https://www.researchgate.net/publication/348370037_Boosting_the_Electric_Output_of_a_Cantilever_Piezoelectric_Harvester_by_Tip_Curvature_Blocking_Elements.
(21) C. Borzea, D. Comeagă, “Reliability of Euler-Bernoulli model for multilayer composite piezoelectric beams,” 11th International Symposium on Advanced Topics in Electrical Engineering (ATEE) (2019).
Downloads
Published
Issue
Section
License
Copyright (c) 2026 REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.